RZN1 WDT & U-Boot/Linux Handling
Hi there,I have the Linux watchdog daemon running and the WDT is working as expected (using rzn1_wdt.c); I've also changed the run levels so the watchdog daemon is started early by init.Now I would...
View ArticleRZ/A1H QT
Dear Chris,I have developed a project using QT5.6 in my RZ/A1H custom board and i have enabled 128MB of SD-RAM as per your suggestion and running application from another QSPI i.e read/write jffs2...
View ArticleRZ/A2M, How do I link the time when the SD card reads and writes files
Hi Sirs,My RTC can work, I hope I can use RTC time.How do I link the time when the SD card reads and writes files?The current time for SD card to write files is always 1980/00/00 00:00Thank you.Best...
View ArticleRZ/N1D: Not able to access port on extension board on No-CM3 mode
Hi,We are using RZN1D along with extension board configured in No-CM3 mode.We are able to access eth1, sw0p0 (CN5) and sw0p1(CN4) but facing problem whileaccessing ports on extension board eth0 (j22),...
View ArticleRZ/N1D U-Boot: keeps rebooting every minute after a development U-boot image...
It still keeps after the good old U-Boot is flashed. What causes this reboot every minute? Watchdog?
View ArticleHow to re-enumerate as custom HID device during run-time without hardware reset?
Hi, we are using RZ A2M processor and trying to re-enumerate the device as custom HID device from device which is initialized as Keyboard HID. What are the steps we need to follow to re-enumerate the...
View ArticleHow to flash .rsu file using e2studio?
Hi, we are using RZ A2M processor and trying to update the firmware. Im trying to verify the firmware as done in the given example rza2m_fw_update_sample_freertos_gcc. But in this example, the rsu file...
View ArticleRunning of user application during startup of Linux
Hi,i have an application which should start automatically after the booting of Linux on RZN1D.and how to get 'systemctl' and 'update-rc.d' commands.I'am using RZN1D board along with extension board in...
View ArticleRZ/G sqlite3
Dear Chris,I need to enable sqlite3 database and the required driver in RZ/G1E yocto based env., can you please help me regarding this it is very urgent for me.Thanks and returnsMahesh R
View ArticleRZ/G2L MIPI-CSI
Dear All,In RZ/G2L User Manual Overview doc, its MIPI-CSI can support "User Defined 8-bit data type 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8".Does it mean "User Defined Byte-based Data types (0x30 to 0x37)"?This...
View ArticleRZ/A2M can record videos on SD card
I wonder if RZ/A2M can record videos on SD card?What's the limitBest regards,Eric Hung
View ArticleHow can i change the vendor id of Ethercat slave?
I developed a CiA402 project based on Renesas's demo.I would like to change the vendor id from 766 to ae8So the ESI file is modified so that there is no 766 in this file.As also the ecat_def.h...
View ArticleUSB COMPOSITE Device (CDC + HID)
Hi,We are trying to use RZ/A2M device as USB composite device (CDC + HID keyboard ) . We were able to configure as CDC and HID separately using the example application given in the...
View ArticlePlan to support DRP-AI in meta-renesas-ai
Dear All,Is there any plan to support DRP-AI (meta-renesas-ai) for RZ/V2L platform? If yes, what's the current schedule?Thanks,Edward
View ArticleRZ/G2H: Cannot turn OFF the LEDs after changing definition in the device tree
Hello Everyone,I am investigating if it's possible to define different GPIO pins for the LEDs (1, 2, 4) and turn ON/OFF from user space.The pin assignment is shown below as defined in...
View ArticleHow to set up RZA2M SDIO wifi package?
Hello!When I was learning the RZA2M SDIO WIFI package, I could not understand how to set up and use the WIFI module.So I would like to ask how to set up a WIFI module?For example, setting up TCP,...
View ArticleRZ/V2L BSP INFO
Dear All,Recently Renesas announced RZ/V2L and I would like to know the below information if possible.***************************1. BSP (Kernel, Graphic & Multimedia) schedule2. DRP-AI schedule3....
View ArticleClik here to view.
UART/SCIFA issue
Hi,Iam trying to send the data via SCIFA in channel 4 (scifa4) at 115200 baud rate. unsigned char *result_String; result_String = "RZ/A2M sample for GCC Ver \r\n";scifa_handle = direct_open("scifa4",...
View ArticleADC and GPIO access in RZN1D in Linux environment
HI,I have an application running on RZN1D board in Linux environment. I need to access ADC and GPIO using this application.Can we use the baremetal drivers of ADC and GPIO in Linux environment? Is...
View ArticleHow to get RZ/A2M unique chip value ?
Hi, we are using RZ/A2M processor. We need the unique chip value per chip ( processor ID / Serial ). As mentioned in this thread , it is said that there will be a register containing the unique chip...
View Article