Quantcast
Channel: Forum - Recent Threads
Browsing all 1583 articles
Browse latest View live

rootfs from sdcard

Hi all,I'am trying to bootfrom sd card so i gave this argumentsi changed fstab file in poky to /dev/mmcblk1p2 and build the image => setenv sd_boot1 'mmc dev 1 ; fatload mmc 1:1 0x48080000 Image ;...

View Article


RZG2L SCIg Channel Smart Card Interface

Hi,RZG2L has Smart Card interface on SCIg channel.I connected Smart Card IC NCN8026A to RZG2L over SCIg channel.I not getting any document for the SCIg channel in Renesas BSP documents.How we proceed...

View Article


SWI call on bare metal RZ/N1S takes 75 to 100 milliseconds

Hi there!I am currently facing a rather strange problem. I have set up FreeRTOS 8.2.0 on a RZ/N1S's A7 core. Works 99% well, but I noticed timings being off.Investigation showed that between the call...

View Article

Plans for creating a DRPAI Gstreamer plugin?

Hi Team, Are there any current plans to create a DRPAI based Gstreamer plug-in? This in theory would enable more flexible use of the DRPAI peripheral. If this concept has already been deemed not likely...

View Article

Program eMMC from U-Boot

Hi,I would like to program the eMMC flash directly from U-Boot, bypassing the need to boot from uSD as described on RZ/G2L SMARC Board by Renesas - Renesas.info and was wondering if that's even...

View Article


ota update for emmc

Hi all,how can i do ota upadte in emmc i'am using rz/g2l boardRegardsTushar

View Article

Serial number - Unique ID (RZ/A2M)

Hi team,Is there any way to get the serial number / Unique ID of the Renesas RZ/A2M chip.I have tried checking the hardware manual, but there is no API or registers regarding the chip serial...

View Article

standyby mode for input control of transciever

Hi all,i'am working on can transceiver this is the dts file of rzg2lin the dts file the standby mode for input control is enabled, but iam not able to find the .c file where they are using the below...

View Article


Boot the EVK from eMMC

Hi,How can the RZ/G2L or V2L EVK be booted directly from eMMC basically utilizing the eMMC boot option by setting SW11 toONOFFOFFONFlashWriter  needs to write the bootloader to eMMC instead of QSPI and...

View Article


Image may be NSFW.
Clik here to view.

How to use i2c to read decimal point in TMP112 ?

https://www.ti.com/lit/ds/symlink/tmp112.pdf?ts=1650424734466&ref_url=https%253A%252F%252Fwww.ti.com%252Fproduct%252FTMP112I'm use e2studio and GR-MNAGO to run in my project.I have seen this...

View Article

RZ MPU User Experience Survey

Hello everyoneWe are currently planning to develop a better user experience for all RZ product users.Therefore, in order to further improve your experience, we would like to hear your requests and...

View Article

Trusted Secure IP in RZG2L

Hi ,Any one using Trusted Secure IP section form RZG2L.It is used in secure booting??Kindly share information .Thanks & Regards.Pravin Raut

View Article

RZ/G2L

HiI am interfacing Tamper sensor with RZ/G2L, there is interrupt to trigger the RZ/G2L while tampering identified How to call ISR in RZG2L with IRQ interrupt.?i am not getting any document related to...

View Article


Adding assembly code to current project

HelloI want to add assembly code to project for MCU RZN1D in IDE: IAR, but many saved words for defining the begin and end of function are not identified in this compiler, for example: ENDFUNCTION,...

View Article

RZ/T1 SPI enable DMA receive problem as a slave

Hello, I encountered a problem when debugging RZ/T1 (R7S910015) as a SPI slave to receive data. When the master chip select enables RZ/T1 to start sending data, the baud rate is 5M, and 6 bytes are...

View Article


SDRAM retention test failure on RZA1H

Hi,Because of the obsolescence issues I replaced the current 2x32 MByte devices with ISSI IS42S16320F -6BLI.However only 32 MB address space in each device is accessed using CS2.Different prototype...

View Article

RZ/A2M HyperRAM 256 Mb

Due to increased memoryI want to change to S80KS2562, 256 Mb: HyperRAMIs there any problem with the driver, and is there anything that needs to be paid attention to?thanks for your suggestion

View Article


Errors in latest Linux BSP 1.0.1 on RZV2L

Hi,I've downloaded the latest SDK for the RZ/V2L, and am trying it out on the EVK. I loaded the upgraded rootfs, dtb and kernel onto an SD card and updated the bootcmd parameter accordingly. I'm seeing...

View Article

RZ/A1H booting issue using SD-RAM

Dear Renesas Team.We are using custom RZ/A1H board, we are able to boot the board using internal 10MB of RAM, but if if try to boot from external SD-RAM of 64MB i.e from etron, the board is not booing...

View Article

Image may be NSFW.
Clik here to view.

How to generate an accurate Complementary pwm of 62.5us in RZ/T1 using MTU3a...

Background:1) RZ/T1 R7S910016CBG2) I want to use MTU3 and MTU4 to generate an Complementary pwm of accurate 62.5us,.But as show below, the clock of MTU3a is PCLCK witch max is 150MHz.if i chose the...

View Article
Browsing all 1583 articles
Browse latest View live