compile kernel for poky
Dear sir/madami'am using RZ/G2L board i have built yoctohow can i compile kernel for pokyRegardsTushar
View ArticleRZ/G2L ethernet voltage domain
Hi I am reading the checklist about RZ/G2L,but I have some questions about the ethernet.The ethernet clock is assigned to 1.8V in the checklist.But the the ethernet power of RZ/G2L could be 1.8V,2.5V...
View ArticleUnable to download Blinky example to M33 core on RZ/G2L
Hi,I'm following RZ/G2L Getting Started with Flexible Software Package (renesas.com) to compile and debug the blinky example on the M33 core in the RZ G2L using e2studio. The example compiles fine but...
View ArticleLatest Pre loader request
Hi Sir/Madam,We are using RZ/G1C MPU P/N R8A77470HA02BGWe would like to have the latest pre-loader for this CPU. Please share.Regards,Bowya
View ArticleHow to configure GPIO Pins in U-boot
I want to set a GPIO pin to high in the u-boot stage.for example the following GPIO pin:Defined at the "rzn1d-db-pinmux.h" file"_RZP(P_GPIO0, RZN1_MUX_6MA(62, GPIO)),/* kGPIO_LED_1 (GPIO0A[25]) */"I...
View ArticleBooting Rz-g2l PMIC EVK Board Getting error while Insert the SD card into the...
As per this Link i tried to Boot the RZG2l SMARC PMIC Board, (https://renesas.info/wiki/RZ-G/RZ-G2L_SMARC)I am getting this Error whi;le entering commands.Attaching Error LOG...
View ArticleSPIBSC booting issue
Dear chris,we are using rz/a2m custom board in which we are trying to enable 2nd qspi for read/write using spibsc driver as per your guidance we have followed the below link and able to build the...
View ArticleRZ/A2M RSPI configuration as slave interrupt
Hi,I want to receive 6400 16 bit data using RSPI . My RZ/A2M is a slave and want to receive in rspi slave interrupt . I have written a test program but it is not working.Below is my...
View ArticleHow to add SCIF and I2C device in rzg2l-smarc.dtsi and build the Image
Hi,We are using RZG2L for our new development.For reference, we are using RZG2L-SMARC-EVK board.I am trying to add extra SCIF uart and i2c channel in the RZG2L-SMARC-EVK board.As per document, I added...
View ArticleCAN issue in RZ/A1H bare metal
Dear Team, i am using CAN protocol example code, which is working properly in RZ/A1H evaluation board i.e of 324bga packages, but in my custom rz/a1h board which uses 256lqf package it is not working...
View ArticleA discussion about software upgrade solutions?
About RZ/T1, renesa support a sample demo " Sample Program for Writing Serial Flash ROM via the USB Microcomputers Incorporating the R-IN Engine "Now I refer the sample test the upgrade solutions which...
View ArticleRZG2L boot form eMMC
Hi Sir/MadamFor RZG2L, I try to boot RZG2L for eMMC and also copy Linux Image in to eMMC.For Coping Linux Image files in eMMC, I refer below...
View ArticleHow to add gdbserver to RZ/V2L image?
Hello Team,I'm trying to add gdbserver to my yocto build. I have set EXTRA_IMAGE_FEATURES ?= "tools-debug" in the local.conf. When I try to rebuild I get the following errors. Can you all point out...
View Articlegenerate .ko during image build
Hi All,i've written hello world program and done a patch copied it inisde linux-renesas_4.19.bb file and when i compile the kernel it generates .ko file when i build the image after writing patch it...
View ArticleHow to improve power savings when suspending A55 clocks from M33
Hi,I'm working on an appilcation on the RZ/G2L EVK where the goal is, to minimize power draw when the A55 CPU doesn't need to work. I've based my POC on the OpenAMP example from Renesas where I invoke...
View ArticleRZ/T1 PDO dynamic mapping problem
1.Previously used TI master +SPI_Ethercat network chip. PDO can be dynamically mapped. 2.Now use Renesas's network code structure. TWINCAT3 feedback PDO can't be dynamically mapped, fixed. 3.Is...
View ArticleMigration from Synergy to RZ/A1
Hello All,My conpany is currently considering the migration from a renesas synergy S7 to a product from the RZ familly. As I'm quiet new to this world, i'd like to ask some questions about this...
View ArticleRZ/A2M GR-Mango LED-BLINKY Project With FREERTOS How To Use Switch To...
Hi guysI am a university intern I am a rookie engineerMy boss want me to familiar GR-MANGO Now I only can use led blinky whatever I wantAnd add switches on my board Now I want to use switch to...
View ArticleHow to add Codec DA7213 in RZG2L-SMARC-EVK WS1
Hi,I am working on Codec DA7213 interface with RZG2L-SMARC-EVK WS1 board.I have Codec DA7213 EVK board, where I can access I2C and I2S lines.I disable the WM8978 codec present in RZG2L-SMARC-EVK WS1...
View Articlebitbake -C fetch linux-renesas
HI all,Iam using this command bitbake -C fetch linux-renesas,what does fetch and linux-renesas, do in the above command RegardsTushar
View Article