Linux Based Renesas Project
Hello,I want to design a linux based project. But i need to linux based desktop version like raspberry pi desktop. I can use raspberry pi but i dont want to use single board computer. i will design my...
View Article800 480 resolution lcd NHD-5.0-800480AF-ASXP-CTP with rz a1 r7s72100 rza...
Hi,I am trying to configure rza linux 4.9 on a r7s721000 to output images to a NHD-5.0-800480AF-ASXP-CTP.pdf (newhavendisplay.com) displayin the .dts file I have the following.../* VDC5 LCD ch 0 */...
View ArticleRSK+RZT2M Dual core example to launch code from xSPI memory
Hello,I am trying to create a very basic program to switch on/off two leds from the two different cores of the RZ/T2M. The idea is to save the whole code into the external SPI memory and launch the...
View ArticleGPIO retention state during Idle and Standby modes.
Hello Team,I want to know the status of GPIO pins state during Idle and Standby modes. Can CPU retain GPIO pins original state either high OR Low whenever it enters into Idle and Standby modes OR it...
View ArticleClik here to view.
Mosquitto support in RZ/G2L
Dear Renesas Team,I have a source code which need to be compiled and which has a mosquitto dependency, as per the other reference in google if we enable meta-networking layer mosquitto dependency...
View ArticleRZ/T2M boot from HyperFLASH duel die with HyperRAM
Hi!Is it possible to boot RZ from HyperRAM / HyperFLASH dual die package.MD0/1/2 = on on off = xSPI1 boot mode (1-bit boot Serial flash)Such as part S71KS512SC0BHB000Edit : MCU would the the 320 pin...
View ArticleRZ A2M Program 'runs away' on some Evaluation Boards
In November, we had a problem that the program runs away, but this was caused by a wrong debugger start address which was set in the example.We got the advice to change the debug start address to...
View ArticleWebviewer issue in RZG2L
Hi,We are using "Renesas WebViewer 91.0esr (Amethyst)" on RZG2L.We are facing some issues with the webviewer, firefox. The major issues are : 1.Even though the internet connection is faster theYouTube...
View ArticleClik here to view.
RZ/G2N bootloader issue
Dear Renesas Team,We have developed a custom board using RZ/G2N processor, we are trying to load the boot-loader to QSPI and were also able to push the...
View Articlerm_motor api in rz-fsp
What is the timeline for adding Motor API to rz/t2m as found on the fsp-ra, such as motor current, driver, encoder, position, hall, sensorless & speed. Will they be optimised for Trigonometric...
View ArticleRZ/G Boot Options
Greetings Everyone !We are designing RZ/G2E into our PCBand came across an issue concerning boot options.Would highly appreciate brief (/any) kind of feedback, thank you very much in advance !Intended...
View ArticleClik here to view.
RZ/V2L booting issue from SD-Card
Dear Renesas Team,We have made our own custom board using Renesa RZ/V2L, we are truing to boot from eMMC and were able to write the flash writer and load the u-boot to eMMC, were able to get the u-boot...
View ArticleClik here to view.
RZ/G Kernel cant mount RFS despite good image and good uSD Card
Dear All,managed to get freshly built U-Boot into Serial Flash of our EK874 RZ/G2E board (worked as described in Startup Guide)... and (thanks to forum member Chris)...managed to get U-Boot to hand...
View ArticleSCI1 serial port does not work on RZ/G2L
Hi all,I am currently implementing 4 serial ports on a RZ/G2L with a Linux kernel 5.10.104-cip3.I use SCIF0, SCIF1, SCIF2 and SCI1 ; they are defined in the Device Tree like this :aliases { i2c0 =...
View ArticleRZ/G2N boot from eMMC
Dear Renesas Team,We are using Hi-hope RZ/G2N evaluation board, we need to boot from eMMC, we are not able to find jumper setting and proper documents to load the boot-loader to eMMC.we have found this...
View ArticleClik here to view.
RZ/G2 Memory Trimming (32Bit down to 16bit)
Greetings, Everyone,would someone know and be able to point us to appropriate file (or files) we can specify DRAM size and width for RZ/G2E ?Intention is to operate DRAM in 16x1 mode (instead of...
View ArticleClik here to view.
RZ/V2M EVK "Set U-Boot Environment" : run bootsd command error.
Hi,On the RZ/V2M EVK, When the "Set U-Boot Environment" commands are executed in the Tera Term, the "run bootsd" command shows this error as "** Unable to read file Image **. as shown below.I am...
View ArticleClik here to view.
RZ/V2L ethernet issue.
Dear Renesas Team,We are using RZ/V2L Renesas custom board, in which we are using RTL8211E ethernet IC, as same used in RZ/G2N Hi-Hope evaluation board, we have added the required driver i.e(...
View Articledocker run makes kernel into panic mode with smarc-rzg2lc
I am following this renesas guide for yocto image installation :https://www.renesas.com/us/en/document/mas/rzg2-group-yocto-recipe-start-guide-vlp-v300?r=1467986 and I have added docker in that...
View ArticleClik here to view.
RZ/V2M DRP-AI Sample application
hi,I am doing DRP-AI sample application in that "RZ/V2M DRP-AI support package version.7.30 Release Note" Network booting section i have some issues.Regards,Aravind S
View Article
