FSP setup for e2 studio in Linux platform.
Hi Team,We are working on a custom board based on RZG2L.But In the documentGetting Started with Flexible Software Package couldn't find any documentation to set up FSP in e2 studio in Linux...
View ArticleRZ/N2L Dhrystone Benchmark
Hi,I am currently working on RZ/N2L. I downloaded the FSP and I am using e2 studio IDE. I tried running Dhrystone program in the board, I got DMIPS/MHz around 1.4. I find the result to be less. I used...
View Articleffmpeg encoding on rz/v2ma
Hi,I would like to encode h264 with hardware acceleration on the RZ/V2MA. I understand that this requires the use of the h264_omx CODEC. Does Renesas have an ffmpeg build for the SoC which supports...
View ArticleTLV320ADC5140 EVK interfacing on RZG2H hi-hope board
Hi All,We managed to interface TLV320ADC5140 evk board using i2c0 which is connected to hi-hoperzg2h eval board. Enabled TLV320adcx140.c in SDK.Our interface connection is:U32--...
View ArticleTLV320ADC5140 EVK interfacing on RZG2H hi-hope board
Hi All,We managed to interface TLV320ADC5140 evk board using i2c0 which is connected to hi-hoperzg2h eval board.Enabled TLV320adcx140.c in SDK.Our interface connection is:U32--...
View Articlecapture module in PWM (RZ/A2M)
is it possible to root pwm to a capture module in RZ/A2M? if yes, please describe it.
View ArticleCapture module in PWM (RZ/A2M)
is it possible to root pwm to a capture module in RZ/A2M? if yes, please describe it.
View ArticleHow to populate Linux Kernel Headers into Yocto/Poky image ?
Greetings,we have a specific driver (.ko) we need to compile , but experience troubles doing so with cross build toolchain.To stop wasting time trying to figure out how to cross compile the driver, we...
View ArticleBlinky example build fail
Hello. I have followed the Blinky tutorial but I get the error message below after the build process. Is there any way to fix this without modifying the source code?Extracting support files... 19:14:34...
View ArticleRegarding RZN1D controller
RZN1d e2 studio ide compatibility? please give me the information? If any FSP support ?
View ArticleRZ_G2M - Need PWM Pins to remain Low state till kernel booting
In BL2 and uboot, we have configured this PWM lines as gpio pins and driving output low to keep the LEDs in OFF state.However, as soon as Kernel loads the pwm rcar driver, this PWM pins goes in high...
View ArticleClik here to view.
PMIC(ISL91302BIIZ) in RZ/G2M EVK
Dear,We have made some sample boards for RZ/G2M and we have followed the schematic of the G2M HiHope EVK.And the PMIC doesn't output the voltage. So, we can do nothing with the sample boards.1. It...
View Articlen2l coremark crc error
The same coremark source code runs normally in ra mcu, but the following CRC-related error is displayed in n2l. What is the reason? I just changed coremark's clock source from systick to gpt because...
View ArticleRZ/N2L cache disabling in e2 studio
Hi, How to disable cache in mpu, i am using e2 studio
View ArticleInterrupt latency program
Hi,Do you have any program to test the interrupt latency in RZ/N2L. I am trying to test the performance of the processor before working on it. It would be helpful if you can provide some source.thanks
View ArticleTesting Audio Codec DA7213 in Hihope-RZG2H
Hi,I am working on Codec DA7213 interface with RZG2H hihope Eval board.I have Codec DA7213 EVK board, where I can access I2C and I2S lines.please find the below Audio codec connection details.We are...
View Articlelibrary for webRTC using RZV2M Evalution Board.
Greetings,We want to obtain WebRTC protocol support using the RZV2M Evaluation Kit, which has MIPI-CSI interface connected to a Sony IMX415 sensor.Additionally, I would appreciate any recommendations...
View ArticleHow to set the core clock of M33? In RZG2L
I have followed multi OS guide to setup the rpmesg demo and it is running fine. However, the clock at which M33 is running seems to be too slow (less than 6 Mhz), I found out by toggling a GPIO and...
View ArticleClik here to view.
[G2L]When I Creat A Project for G2L With FSP ,I Can't editor The Pins
As the title pins config is grey
View ArticleCapture compare pulse in RZ/A2M
i need to run the stepper motor by implementing Scurve in it.. after acceleration i need to run the stable state of scurve without delay and deceleration in between each process i need to run without...
View Article