Build SDK for RZ/N1 using Yocto
Hi,I was following Yocto build setup for RZ/N1D using RZN1-Linux-User-Manual.pdf, but I couldn't find a description on how to build SDK.Could someone please help?
View ArticleRZ/N1 SDK missing asm/socket.h
I built an SDK for RZ/N1D and tried to build simple application for capture packets using pcap, but I'm getting following error on compliing. I check the include directories but couldn't find an "asm"...
View ArticleAccessing 5 Port Switch from Linux
Hi all,Is it possible to configure the 5 Port Switch from Linux (in No-CM3 mode)? If yes, how is it done?I see that there is a driver from MoreThanIP to access the switch, but no examples are available...
View ArticleTo test PCIe slot on RZG1N
Hi,We are working on RZG1N development kit and need to test the PCIe slot. How can we test the PCIe slot on RZG1N with TG-3468 Gigabit PCI Express Network Adaptor? Kindly help regarding this issue....
View ArticleRZ/A1 How do I add USB?
I am working on adding the USB to a RZ/A1. The RZ is running freeRTOs with 4 different tasks (1ms, 10ms, 20ms and 100ms task). The RZ need to be setup as a host. Do you have a sample code somewhere...
View ArticleAdding Support for TG-3468 Gigabit Network Adapter
Hello Everybody,We're working on RZ/G1N board. To test PCIe port present on the Carrier board, we have connected the Network Adapter. unfortunately its not working, i am not able to see it by running...
View ArticleSpecification or reliability differences between the R7S721000VCFP and...
Are there specification or reliability differences between the R7S721000VCFP and R7S721000VLFP Part numbers? On page 72 of the RZ/A1 Hardware manual found here...
View Article64MB SDRAM in RZ/A2M
Hi alli have enabled 64MB SD-RAM in RZ/A2M board with ISSI sdram part this is working perfectly fine, i want to use another SDRAM part i.e of etron which is of same pin compatible,same hardware and...
View ArticleRZ/G1E master slave concept
Hi all,I want to enable USB-CDC functionality in RZ/G1E i.e when i connect USB-micro cable to my board it should detect as com-port(i.e /dev/ttyUSB0) without using any external rs232, please help me...
View ArticleGPIO Interrupt Handler
Hello Everyone,I am Trying to configure one of the GPIO pin in i-wave RZ/G1N to generate interrupt . Please let me know where to write the handler if interrupt is generated.Thanks,Mohd Habeeb Ur Rehman
View ArticleRZ/T1: Adding SPI Communication into the CiA402 sample program
Hello everyone,currently I'm developing an EtherCAT slave with the CiA402 drive profile on the RSK+ for RZ/T1. There is a sample program (an-r01an3169jj0110-rzt1-ethercat) on the Renesas website which...
View ArticleChanging Debug Port from SCIF0 to SCIF3 in RZ/G1N
Dear All,We're working on a RZ/G1N i-wave carrier Board , where SCIF0 port is configured as Debug port to see the boot messages on the serial terminal. We're planning to change the debug port from...
View ArticleChanging Pin Functions of RZ/G1N SOM
Dear All,We're working on RZ/G1N i-wave Development board, How to change the pin functionality of the SOM board. Please let us know which file in the source code need to modify in this...
View Articlehow to configure gpio edge triggered in user space
Hi, I am working on RZA1H evaluation kit , I have an Application which will wait for edge triggered interrupt from a gpio(gpio polling Algorithm). But when i export gpio to user space,unable to find...
View ArticleRenesas Starter Kit+ for RZ/A1H Touch screen issue
Currently i am working on RSK based with touch display. using linux bsp 4.9 and using same Focaltech FT5X06 5 point touchscreen hardware and driver. But its touch getting some issue.I have tested the...
View ArticleTick counter / Timer on RZ/T1
I'm trying to time operations on the RZ/T1 and looking for the easiest way to do so. I need to do this on the R4 processor, running ThreadX and the M3 with the micro ITRON hw OS. Any input would be...
View ArticleRZ/A1 Linux-4.x BSP Porting Guide is incomplete?
I am trying to boot linux on the YLCDRZA1H board, but the porting guide is incomplete. So far I've been able to get U-Boot running, but just using the "./build.sh jlink" command for DTB, Kernel, and...
View ArticlePrinting the Debug messages over the ethernet
Dear All,We're currently working on RZ/G1N i-wave development board. How to print the boot debug message using Ethernet port rather than debug-port(SCIF0) which is selected by default. Thanks,Mohd...
View ArticleDT070BTFT-PTS1 Display Settings for RZ/G1N Board
Hi,We're working on RZ/G1n Development board. which has "ETM070001ADH6" LCD connected to it. Now we're planning to replace that LCD with "DT070BTFT-PTS1". Please let us know what are the changes need...
View ArticleHow to restart when watchdog times out
We become indebted to.My name is CHIX.The software watchdog is verified on the CPU board on which RZ/G1E-PF is mounted.Linux kernel4.4.138-cip25-yocto-standardI was able to confirm that everything...
View Article