Clik here to view.
Failed to Generate LKM module for RZ/G1N
Dear All,I've been trying to cross compile the display module(panel-tfp410.c) for RZ/G1N. after assigning the MACRO with =m in .config file i am getting the following error shown in the picture...
View Articlespidev not working
Hi , We have a customized RZG1E board with CIP 35. We enabled spidev in our board as below:&pfc {msiof2_pins: spi3 { renesas,groups = "msiof2_clk", "msiof2_ss1", "msiof2_tx",...
View ArticleNoise occurs on video with VSPM filtering
Hi all, I am trying a scaling and displaying on RZ/G1H(iW-RainboW-G21D + CIP4.4.185).When resizing with VSPM filter, green noise occurs at the right and bottom edges of the video.Here is my command....
View ArticleHow To add PWM Node into Device Tree for RZ/G1N Board
Hi There,We're Working on RZ/G1N SOM board. Our customized carrier board has two PWM(1 & 2) channel on one of its Expansion Connector(PWM3 channel is used for backlight ). We need to configure...
View Articletoolchain dependency to build 4.9 kernel
Hi We are using RZ/A1 processor based custom target board . linux kernel version is 4.9.123 ( downloaded from renesas site).we are trying to update to latest version of arm-linux-gcc toolchain from...
View ArticleDecoding JPEG with VSPM filter.
Hi all, I am trying to display JPEG images from IP cameras on RZ/G1H(iW-RainboW-G21D + CIP4.4.185).Following is my command. gst-launch-1.0 appsrc ! jpegparse ! jpegdec ! videoconvert ! video/x-raw,...
View ArticleRZN1D reboot doesn't work on prototype board
Hello, I am trying to reboot my proto board (which is using an RZN1D).From Linux, if I execute the "reboot" command I can trace execution to the rzn1_restart function where the registers RSTEN and...
View ArticleRZG1E secure boot re-encryption problem
Hi, We have a customized board on RZG1E processor with 1GB RAM.I am trying to enable secure boot on rzg1e.But while re-encrypting the encrypted kernel on board using InstallToll.It stops at this...
View ArticleClik here to view.
My Question is the relation between MRESET_N and iMRESETn signal ?
Hi,As in the processor Document, The boot latching is with respect to MRESET_N going high but, in the waveform i see there is iMRESETn signal. 1. I need to understand the relation between MRESET_N and...
View ArticleClik here to view.
How much time it takes for Booting RZ/N1D ?
Hi,We are using QSPI Booting mode in RZ/1D Processor . Is timing considerations for Booting correct ?Power - up Sequence + Boot sequence images are attached for reference :1. Power Up sequence 2. Boot...
View ArticleIssue with weston LVDS display.
Hello, we are facing issue with the weston LVDS display. please find the configurations and observations captured in the excel sheet attached. Can you please help us to resolve the color issue in...
View ArticleRZ/N1: can we connect both GMAC to the switch
Hi there,My goal is to have a single Ethernet port that is connected to both GMAC of RZ/N1D: GMAC1 being run by Linux on dual A7 and HW-RTOS GMAC managed by M3. Alternatively, we may also want to...
View ArticleRZ/N1D: access to QSPI after boot and update
Dear forum,I'm trying to access the QSPI MX25L25635F flash from the RZ/N1D dev board after boot for RW. Our idea is to update a program (and make it persistent) after linux boot while running. We would...
View ArticleRZ with TFT 1280x800 LVDS24bit input
Hi,I have to manage a tft with 1280x800 resolution: the display has 24 bit lvds input.Is there any way to use the lvds interface of RZ to drive the TFT ?I am forced to use the RGB interface and convert...
View ArticleRZ/T1 MCU
Hello. We plan to be new designers of the RZ/T1 MCU. we need to connect a FPGA to the MCU for deterministic serial data streams (target is 200Mbps) . Can we use the SPIBSC for that (shared with the...
View ArticleClik here to view.
enabling 128 SDRAM in RZ/A2M
Hi all,I am using RZ/A2M custom board, i have enabled 64MB SDRAM successfully, now i am trying to enable 128MB SDRAM and the configuration is 16-bit of 2 chips(SDRAMs) sharing same address pins...
View ArticleClik here to view.
Sync0 ISR jitter issue in EC-1/RZ-T
I use EC-1 to make a EtherCAT slave device, and indeed EC-1 is a function reduced version on RZ-T, so I post this question here.Now , EtherCAT DC can work well in the DC mode , but I want to check Sync...
View ArticleRZ/T1 for Encoder Protocol Interface
Greetings,My question is related to RZ/T1 MCU, What (features) makes it a distinguished choice among other MCU's when it comes to absolute encoder protocol interface such as HIPERFACE, BiSS, and...
View Articlecan't find R01AN4477EJ and R01AN4321EJ
I have the evaluation board kit for RZ/A2M. And in the "Quick Start" manual step 21， it says we can get the files R01AN4477EJ and R01AN4321EJ to test the board. However, when searching the name of file...
View ArticleCan't find handgesture demo soft package
https://mp.weixin.qq.com/s?__biz=Mzg5MDA4ODg1NQ==&mid=100006351&idx=5&sn=5b713c38e1ca5e95c1c7e95f26322357&scene=19#wechat_redirectI can't find the handgesture-camera demo soft package...
View Article