i2c slave with 0x60 address can not detect with renesas RZ/G2LC
I am using renesas RZ/G2LC. I have attached i2c slave device on PMOD1(pin 3- SCL pin4 - sda pin2 -GND pin1-vcc) but my device is not detecting. Then I found out(i2c-core-base.c) slave devices with the...
View ArticleClik here to view.
RZ/T2M kit cant run to hal_entry()
my RSK+ RZT2M board is good at first，Reference documents rzt2m-getting-started-flexible-software-package.pdfFigure 2: Boot MODE SW Setting Description SW4.1 ON 16-bit bus boot mode (NOR Flash) SW4.2...
View ArticleClik here to view.
RZ/T2M kit cant run to hal_entry()
my RSK+ RZT2M board is good at first，Reference documents rzt2m-getting-started-flexible-software-package.pdfFigure 2: Boot MODE SW Setting Description SW4.1 ON 16-bit bus boot mode (NOR Flash) SW4.2...
View Article9DML4493A - PCIe Gen5 clock Multiplexer Glitch free or not
Hi,We are using 9DML4493ANLGI in our design for PCIe clock distribution. In the datasheet it's mentioned that "Glitch-free output enable pins for each output". Does this mean we need to toggle O/P...
View ArticleClik here to view.
manual install intltool-native-0.51.0-r0
Dear,When I build the BSP v1.4 for G2L in ubuntu 20.04, there is a warning message as follows.How do I install it manually?"bitbake core-image-minimal"Thanks,
View ArticleCan we use QT official source for RZ/G2L SMARC
Hello, Can we use Qt official source (https://download.qt.io/archive/qt/) and build Qt for RZ/G2L SMARC by Cross Compiling against the Renesas BSP SDK instead of using the Qt version provided...
View ArticleProblem translating mobilnetv3 onnx model to DRP-AI format.
Compare input/output shape definition in ONNX and pre/post YAML file. Warning YAML defined size(input_to_body) is different from ONNX's size definition. -> Size defined in YAML file will be used....
View Articleemmc flashing through jtag
Hi all,i'am trying to flash the image, uboot through jtag where can i get addresses of all these in emmcRegardsTushar
View ArticleFacing issues with E2 studio for RZ/A2M
Hi all,Am trying to boot up RZ/A2M using e2 studio. I tried the blinky application, it compiles and uploads perfectly fine, but doesn't execute properly. Am I missing some settings?When I tried the...
View ArticleSK-RZG1M: access SATA from U-boot
Hello,I'm currently using SK-RZG1M board for my tests and I'm trying to access SATA from U-boot.I'm using the "porter.h" configuration from elinux.org U-boot sources. Is there any SATA driver...
View ArticleHow to bring up RZ/T2M SCI/UART (USB serial port: USB Mini-B:CN16)?
Hi,I have an EVK RZ/T2M board. To bring up RZ/T2M SCI/UART (USB serial port: USB Mini-B:CN16), I have done the steps below.1) Installed e² studio tool, FSP packs, GCC toolchain and other necessary...
View ArticleClik here to view.
RZA3UL board for Initial Program Loader
Hi AllI'm trying to get the RZA3UL board(QSPI Edition) to work.I followed the Initial Program Loader Application Note, but it seems that the download does not work as a U-Boot message appears in the...
View ArticleIAR debug fail on RZ/N2L board through J-Link OB debugger
Hi,I bought Renesas Starter Kit+ for RZ/N2L (Cortex-R52) for development, and install development tool linked in www.renesas.com/rskrzn2lI create RAM-based FSP Blinky program for IAR, and debug it on...
View ArticleWorking of GPIO on RZ/A2M
Hi all,Am trying to make the GPIO work on RZ/A2M, such that I can map it to a physical pin to observe it on an oscilloscope.I am using the led code as a reference and trying to make the PORT_D_PIN_3...
View ArticleClik here to view.
RZ/N2L Group EtherNet/IP OpENer Sample Program Package ，need CODESYS...
I downloaded the [RZ/N2L Group EtherNet/IP OpENer Sample Program Package] project from the Renesas website and the documentation suggests CODESYS 3.5.15.10 32-bit, but I can't find this version. I...
View ArticleRZ/G2L booting
Dear Sir/Madamhow does rz/g2l board boots(booting sequence)RegardsTushar
View ArticleClik here to view.
CAN0 (CAN bus) listen-only
Hi allI tried to put the can0 into listen-only mode, but the system returns "Operation not supported"Is it an unsupported feature of the Renesas canfd controller, or is it unsupported because it is not...
View ArticleClik here to view.
RZN2L TSN and HSR demo？
1、RZN2L Integrated TSN-Compliant 3-Port Gigabit Ethernet。2、Does N2L support HSR3、I want to use two boards to test TSN and HSR. Is there any demo project that can be downloaded? Is there an application...
View ArticleRZ/G2l Custom board, Linux boots extremely slow randomly.
Hi All,I have been working with a custom board with RZ/G2l MPU, This board is made with RZ/G2L SMARC reference board as reference.We are using the PMIC version and PMIC is working with its default...
View ArticleRZ/G2L When we disable the logs in ARM Trusted firmwarebl31_main, device wont...
Hi All,When we disable the logs in ATF, device wont boot.I Have been trying to boot with ATF without any logs in the console. But I observe that we need to enable at least log level NOTICE for the AFT...
View Article