Quantcast
Channel: Forum - Recent Threads
Browsing all 1583 articles
Browse latest View live

RZG2UL: MTU3 PWM 100% duty cycle issue

We are using RZG2UL SOC based custom board with Linux BSP version 3.0.3.When using PWM mode for MTU3 (MTIOC3A) pin. We are facing below issues for PWMIf PWM is disabled the pin goes to high stateIf...

View Article


P24 bank pins configuration issue in RZ-FIVE

Hello,We are configuring P24 bank pins for below interfaces and below is the dts configurations for the same.SCIF4:TX: P24_5 ALT5RX: P24_4 ALT5Below is the dts pinmux configuration: scif4_pins: scif4 {...

View Article


Re-enable lower prio interrupt during higher interrupt

Hello,We use a RZ/A2M, osless.We have a higher prio (prio 5) interrupt, which may take some longer time in some cases.Therefore we want to re-enable all interrupts ( this can be done by using...

View Article

Image may be NSFW.
Clik here to view.

Regarding pwm configuration with custom rz g2ul board

Hi Team,I have configured MTIOC7A pin as PWM output for LCD back light PWM. Here below I have attached screen dump of schematic for your reference purpose.Used Device Tree r9a07g043.dtsi  => mtu3:...

View Article

RZG2UL: PWM issue with 0% and 100% duty cycle

We are using RZG2UL SOC based custom board with Linux BSP version 3.0.3.When using PWM mode for MTU3 (MTIOC3A) pin. We are facing below issues for PWMIf PWM is disabled the pin goes to high stateIf...

View Article


RZG2UL: Ethernet: Not achieve 1Gbps throughput properly

Hello,We are using RZG2UL based custom board with AR8031 Gigabit Ethernet PHY with Linux 3.0.3 BSP.Ethernet is configured and working properly but when calculating throughput for 1Gbps speed using...

View Article

Image may be NSFW.
Clik here to view.

EMMC

hi sir,i am tried to do emmc loader work with RZV2M evk.i was struck over "Please send binary file!", Please find the attached image below.Already I downloaded the boot loader and u-boot fileThen, the...

View Article

eMMC as boot media support in RZ-FIVE

Hello.Currently for RZ-FIVE in v3.0.3 BSP, only QSPI boot is supported. When we try to boot from eMMC below error is observed:U-Boot SPL 2021.10-g711334a179-dirty (Apr 18 2023 - 11:58:08 +0530)SPL:...

View Article


RZ/V2MA Sample application

Hi Team,I am working in RZ/V2MA board to build a ML/DL application.I am trying to build application using yolov3-tiny. I tried to convert the yolov3 (app_usbcam_http) sample application to yolov3-tiny...

View Article


RZG2UL: CANFD: data transfer not happening for higher bitrate

Hello,Currently we are testing CANFD with channel0 in RZG2UL SOC based custom board with Linux 3.0.3 BSP.When data bitrate is set to 2Mbps or lower CAN data transfer is working properly.When data...

View Article

RZ/V2M U-boot: "Bad Linux ARM64 Image magic!"

I have built the image for RZ/V2M (SOC_FAMILY = "rzv2m:r9a09g011gbg") as described in "RZ/V2M Linux Package Start-Up Guide".I'm getting errors as below.[BL1] Loaded the 2nd boot loader [BL1] Kick the...

View Article

RZG2UL: Running M33 core application from Uboot

We are testing M33 core on RZG2UL evk board.We tested rpmsg demo application given along with vlp3.0.1 BSP and it is working.After compiling blinky application in e2studio for G2UL evk blinky.elf...

View Article

Image may be NSFW.
Clik here to view.

To set the static IP in RZ/V2M

I need to do ssh from the LAN but the IP of the board is not stable. I tried to make it static so I tried to set the static IP from the /etc/network/interfaces file. I have set the static IP of the PC...

View Article


Run the C++ application on linux RZ/V2M board

I need to run the C++ application and some custom applications on RZ/V2M Linux board. How can I install the dependencies and set up the G++ environment for the C++ libraries? Can you suggest some...

View Article

RZ/V2M MIPI CSI Interface not getting detected.

Hi All,I want to interface IMX415 camera Module (https://www.bhphotovideo.com/c/product/1305323-REG/computar_a3z2812cs_mpwir_1_2_7_2_8_8_5mm_f1_2_manual.html) with RZ/V2M, i'm using...

View Article


Require RZ/V2M Driver and Build Process

Hello TeamWe successfully built the core bsp image for the RZ/V2M (SOC_FAMILY = "rzv2m:r9a09g011gbg") using the "RZ/V2M Linux Package Start-Up Guide" while working on the RZ/V2M Eval board. Currently,...

View Article

RZG2N CAN0 and CAN1 Not working

Hi All,We are working on RZG2N based Custom board and trying to check CAN0 and CAN1 and we are using 4.19 kernel, When we try to test CAN interface we are getting the below error,We tried on RZG2N...

View Article


Run script automatically on startup.

Hi All,I want to clear up some doubts related to the development using RZ/V2M Board eval kit v2.How to open menuconfig and related settings to customize the application.where can we find package...

View Article

Image may be NSFW.
Clik here to view.

RZV2M eMMC BOOTING

Dear Sir,I follow the same procedure as per the "Linux Strat-up Guide". Booting files are uploading are done through the eMMC in tera term, but, after completion of eMMC sending files.When i re-run the...

View Article

RZV2M EVK board COMM port issue

Dear sir, when i am connect the RZV2M evk kit to WINDOWS os for tera term, in teraterm not showing the serial port.When i connect kit to PC through the usb port, the system shows usb port is not...

View Article
Browsing all 1583 articles
Browse latest View live